Just purchased a Gen2 -- items to refresh before tracking?

All things specracer!

Novice Typer
Novice Typer
Posts: 14
Joined: Tue Apr 03, 2018 10:07 pm
PostPosted: Wed Apr 04, 2018 10:06 am
Hi folks. I owned a SRF for a few years in the early 2000's (ran in MARRSS mostly), but decided to sell around 2004 due to young children, etc.

I've done a lot of track days the last several years with street cars (NJMP mostly, some at Summit and VIR) and recently decided to switch back to a SRF for a track day car this year with the possibility of racing at some point (late 2018, maybe 2019).

So I just picked up a Gen2 in great condition (thanks Todd!) that finished top 10 at the Indy runoffs last year and had good results in other events throughout the year.

Looking through the car last evening, everything looks in good shape. My local non-CSR shop can't take me for a checkup for two weeks, and I have not heard back from my local CSR, so I'm planning to do a few things and then take it to my next track day next week.

Here are the things I'm planning to do just so I have a baseline for maintenance:

    Safety check on all suspension fasteners
    Change engine oil and filter
    Change trans fluid
    Replace rotors (front slots still visible, rears partly gone)
    Replace pads
    Flush brake fluid
    Replace air filter
    Top off water (add water wetter?)

My belts expired 2017 so I'll order replacements but will go ahead and run them (non-SCCA track day).

Can you guys/gals suggest anything that I've missed?

Thanks!

John
SRF #852 Gen2 (current) - purchased 3/18

SRF #835 Gen2 (previous) - owned 2000 - 2003

Novice Typer
Novice Typer
Posts: 14
Joined: Tue Apr 03, 2018 10:07 pm
PostPosted: Wed Apr 04, 2018 10:20 am
Just found these very handy checklists from Kanga. What a great resources!

http://www.kangamotorsports.com/maintenance-checklists/
SRF #852 Gen2 (current) - purchased 3/18

SRF #835 Gen2 (previous) - owned 2000 - 2003

Ready to Write a Book
Ready to Write a Book
Posts: 98
Joined: Fri Apr 22, 2016 5:11 pm
PostPosted: Wed Apr 04, 2018 10:31 am
Things most likely to disable the car NOW:

1. Wheel bearings.
2. CV joints (and boots).
3. Axle nuts (loose).

Novice Typer
Novice Typer
Posts: 14
Joined: Tue Apr 03, 2018 10:07 pm
PostPosted: Wed Apr 04, 2018 11:10 am
Greg-Cirillo wrote:Things most likely to disable the car NOW:

1. Wheel bearings.
2. CV joints (and boots).
3. Axle nuts (loose).


Perfect, I'll check these over the weekend.

Thanks Greg!
SRF #852 Gen2 (current) - purchased 3/18

SRF #835 Gen2 (previous) - owned 2000 - 2003

Novice Typer
Novice Typer
Posts: 14
Joined: Tue Apr 03, 2018 10:07 pm
PostPosted: Wed Apr 04, 2018 11:12 am
Calipers, rotors and pads are still from a 1983 Renault Alliance/Encore, right?

Since I'm not racing, but only running track days for now, I'm thinking of just getting Centric rotors and pads for about 25% of the price of Enterprises parts.

Is this a bad idea?
SRF #852 Gen2 (current) - purchased 3/18

SRF #835 Gen2 (previous) - owned 2000 - 2003

Ready to Write a Book
Ready to Write a Book
Posts: 98
Joined: Fri Apr 22, 2016 5:11 pm
PostPosted: Wed Apr 04, 2018 11:22 am
JohnSoPA wrote:Calipers, rotors and pads are still from a 1983 Renault Alliance/Encore, right?

Since I'm not racing, but only running track days for now, I'm thinking of just getting Centric rotors and pads for about 25% of the price of Enterprises parts.

Is this a bad idea?


For a track day car, I'd still get the Hawk Spec brake pads. I have two brand new non-vented rotors I'd be happy to donate to you.
User avatar
Needs a Life!!!
Needs a Life!!!
Posts: 740
Joined: Mon Dec 05, 2011 10:03 am
Location: Greenwich, Connecticut
Chassis:
860
PostPosted: Wed Apr 04, 2018 12:31 pm
On the subject of axle nuts, keep an eye on them.

At the front, always check the castle nut cotter pins. If they come off, then they snapped off. That means the bearing /hub is partially seizing, which precurses imminent wheel bearing failure.

At the rear, I suggest you swap out the outer nyloc nuts for fresh new ones. Torque to at least 160 lb ft. Check that torque every three or four runs. If you have to keep retorquing, and the wheel nut is fresh, you're looking at a rear bearing that could be any minute from failure.
User avatar
Forum Hermit
Forum Hermit
Posts: 111
Joined: Fri Sep 22, 2017 5:02 pm

Chassis:
615
PostPosted: Wed Apr 04, 2018 8:12 pm
I will take these words of wisdom also! Why is it that the bearings seem to be such shit?

John if you do decide to get rid of the Spec brake equipment let me know. I am still looking for brake parts for my build.
Chris B
Chicago Region
Flagging and Communications / Emergency Services

Good chance you have seen me waving flags like a crazy person at some point.

Needs a Life!!!
Needs a Life!!!
Posts: 389
Joined: Fri Dec 02, 2011 6:02 pm
PostPosted: Wed Apr 04, 2018 11:33 pm
Coolant?

Ready to Write a Book
Ready to Write a Book
Posts: 98
Joined: Fri Apr 22, 2016 5:11 pm
PostPosted: Thu Apr 05, 2018 9:19 am
TrackBrat wrote:I will take these words of wisdom also! Why is it that the bearings seem to be such shit?


Hit or miss, actually. I've got a couple that are going on two+ full seasons. If you don't know their age or origin, you really have to expect the worst. I hear good things about the new-new bearings.

PS: I had made a habit of pulling new bearings apart, cleaning out the lube, and re-lubing with Moly-based synthetic. But the new-new bearings can't be pulled apart (at least not by me), so you're relying on whatever lube they used during assembly.
Next

Return to General Discussions

Who is online

Users browsing this forum: Google [Bot] and 12 guests


cron