The tank cracked due to a weird vertical wreck where the tail section flapped down onto the tank from above. It's a very narrow crack in the middle of the weld about 3" long.
I'll probably get it re-welded but if I can't get that done in time for the next race, would JB Weld hold for a weekend?
Cracked weld in my coolant tank. JB Weld OK for a bit?
16 posts
• Page 1 of 2 • 1, 2
JB Weld is a great product for shear stress applications in stable temperature locations. I'm not sure I would trust it for non shear pressure retention over multiple heat cycles in a environment that this application would require. Could work but I wouldn't risk my weekend hoping it would hold.
At the very least bend a piece of metal longer than the split at 90 degrees then attach it to the tank using JB Weld so the stress on the repair is in shear in two directions. (Personally I would take it to my neighbor who owns a fabricating shop and could have saved the titanic by welding wet toilet paper in the hole, but clearly you lack that option) Clearly an opinion as I have never tried it, good luck It's better to be last on the grid at a race track, than have pole position at the Funeral Home.
|
|
I had this happened twice (arggH!) and used an epoxy designed for wet applications (emergency fix at the track.) It hardened sufficiently within a hour to get through the weekend (only a minor drip came through and it survived a couple of weekends until I got the tank replaced once, and repaired another time.). It comes in a roll (sort of a fat "Tootsie Roll" looking affair). You cut off a piece with a knife then knead it to blend the two parts together. I pressed it over crack in the aluminum weld bead (the problem area), overlapping at least an inch in all directions.
Bob Breton - SRF 51 - San Francisco Region
|
|
Hey, Bob, what's the brand name of that epoxy? Sounds like handy stuff to keep around. |
|
Curious about how many others have experienced cracks in these tanks? We've cracked two within the last year. These are not cheap to replace. Any thoughts about how to prevent this problem?
|
|
Needs a Life!!!
Posts: 228
Joined: Wed Dec 28, 2011 6:21 pm Location: Stillwater, Mn Chassis: 784 |
I've had the same tank for 16 years and never had it leak.
|
Still Learning to Type
Posts: 32
Joined: Sat May 17, 2014 12:08 am Location: Farmington Hills, MI Chassis: 214 |
Mine did this Saturday at Grattan Majors, after qualifying, while I was idling my way to impound. Water temp had reached only 187 while I waited for traffic. Then, poof, steam wafted over my head.
|
Forum Hermit
Posts: 102
Joined: Tue Nov 29, 2011 10:53 pm Location: Off the apex... Chassis: #204 Facebook Page: http://facebook.com/jerry.aplass |
Ha! Some thing happened to me at the exact same place - crack in the weld... Luckily there was someone at the track that could weld it (They could see the desperation on my face so it was not cheap )
Jerry Aplass SRF #204
San Francisco Region "Straights are for fast cars. Turns are for fast drivers." - Colin McRae |
Exactly the same crack we just had.
|
|
Needs a Life!!!
Posts: 1200
Joined: Wed Nov 30, 2011 1:38 am Location: Sunnyvale, CA Chassis: 068 415 Facebook Page: http://facebook.com/HSERacing |
I think the 90 degree angle is the problem with the weld in the first place. Seems like I read somewhere that is why most pressure tanks have rounded edges. Dave Harriman
"It looks crazy, I understand. But, we only live once and I am going to give it a good try." - Alex Zanardi |
16 posts
• Page 1 of 2 • 1, 2
Return to Technical and Repair Discussions
Who is online
Users browsing this forum: No registered users and 0 guests